Category: Blog
-
Maxphotonics laser source FORWARD LIGHT ALARM
Cause Analysis 1 input Power voltage less than AC190V 2 Module damage caused by cutting highly reflective materials Solutions 1 Check Voltage and add a AC voltage regulator ，Let the voltage stabilize between 210-230V Detect signal line voltage in burst state:a First use a multimeter to measure whether the DC voltage of the adapter board…
-
YASKAWA SERVO ALARM 710 720 Solutions
Laser cutting machine XYZ shaft 710,720 alarm Failure analysis. The 710 is instantly overloaded. The 720 Continuous maximum load. Cause analysis 1 Motor cable, encoder connectionPoor wire or connection 2 The motor exceeds the overload protection featureSex while running 3 Guided by mechanical factorsThe phone does not drive, causedExcessive load at runtime 4 Servo unit…
-
Warning！！！ Laser reflection problem
Laser welding machine, in welding aluminum alloy, copper alloy, and other highly reflective materials There will be a risk of injury After a long time of testing, the laser welding machine does not have the safety advertised by some manufacturers, but there are great safety risks. When welding materials with high reflectivity, there will be…
-
Focus lens Collimation lens DF125 DF150 DF100 D30F200 Series Apply and replace
Focus lens Collimation lens DF125 DF150 DF100 D30F200 lens unit 120AH0600A lens unit 120AH0700A lens unit 210CLA1013 lens unit 210FLA4023 lens unit 210FLA4032 lens unit 120AG0600A lens unit 120AG0610A lens unit 120AG0700A lens unit 120AG0800A lens unit 120AG0900A lens unit 120AG1400A lens unit 120BH1001A lens unit 120BH1006A lens unit 120A30700A lens unit 120AU4500A lens unit…
-
Advantages and disadvantages of laser welding machine
(1) The position of the weldment must be very precise and must be within the focus range of the laser beam;(2) When the weldment needs to use a jig, it must be ensured that the final position of the weldment is aligned with the welding point that the laser beam will impact;(3) The maximum weldable…
-
Manual focus updated to Autofocus laser head
Manual focus laser head using to 3000W power or less, to save costs, but when cutting, the perforation process is very difficult for thick plates. Different parameters correspond to the same focal length, and the processing efficiency is low. For the most demanding fast cutting, it is recommended to replace the auto-focus laser head. With…
-
500-1000W max brand laser update to 2000W IPG solutions
YLR-2000-MM-WC 信号线连接方式 Analog control connection solution the Signal cable form IPG like that (i ready the No.1,4 cable ; No.2,3 cable ,No.8,9 cable is short ) { No.10-11 is a key for Laser source }; No.15-No.16 cable is for PWM+ and PWM- Network Plug connect to PC PWM 3766PWM+—-to 4516E Board PWM+——to CON1——-out NO1 to laser source PWM+…
-
The diffirent operation for memory
1.Step for opening IPG Just like the picture ①Key②Laser on③Shutter④Aiming Then,you can normally to use 2.Step for Calibration Press F1 to calibrate Selec”2” to do capacitance calibration Move laser head approach the board Move laser head approach the board Then save
-
There is a problem with material cutting – there is no straight line cut, there is a wave.
For this question, Check whether the belt has loosen due to long time running 2. Check whether the ratio wheel has loosen or not 3. Decrease the cutting speed B) There is also a problem with holding the desired cutting dimensions – a square should be 25mm which is set, but the final cut is…
-
Inspection before processing when you get a new laser cutting machine
加工前检查 Inspection before processing 配电柜供电电源线松动 Check whether the power supply line in the control cabinet is loose 2、依次检查床身，光纤器，水冷机，空压机，风机 Inspect the lathe bed, laser source, water chiller, air compressor, exhaust fan 3、检查气瓶气管，气量 Inspect the cylinder and pipeline, gas valume 4、机器床身杂物清理床身与外设设备影响切割的安全隐患 Clean up the objects on the lathe bad and peripheral equipment that had danger risk on…